iGO Primo, NextGen - dodaci, skin, branding, lang, voice, ux, poi, speedcam...
- Začetnik teme vladcepesh
- Datum pokretanja
UREDNIK
- Učlanjen(a)
- 07.03.2011
- Poruka
- 2.980
Skidaj sa JDownloaderom i ne treba ti!
- Učlanjen(a)
- 16.08.2014
- Poruka
- 314
scdb iGO Speedcams [19 November 2014]
November 19 / 2014
Africa
America
Asia
Europe
Benelux
Western Europe
Eastern Europe
Skandinavia
November 19 / 2014
Africa
Kod:
http://www.tusfiles.net/ukxa0q8e8qpzAmerica
Kod:
http://www.tusfiles.net/skdwez989yutAsia
Kod:
http://www.tusfiles.net/617aqoe0u1ujEurope
Kod:
http://www.tusfiles.net/7o04rsmywz2iBenelux
Kod:
http://www.tusfiles.net/f0wurt8inwnrWestern Europe
Kod:
http://www.tusfiles.net/nxc4ur8pgj41Eastern Europe
Kod:
http://www.tusfiles.net/hrc1wuj1ufxuSkandinavia
Kod:
http://www.tusfiles.net/5fya40ri1e4rVec su obrisane. Je l' moze opet?
- Učlanjen(a)
- 09.08.2012
- Poruka
- 134
Jel zna neko gdje da pronadjem HUD za rezoluciju 320x480,znaci treba mi samo HUD a ne da ubacujem neki od skinova jer mi oni uglavnom poremete rad iGO-a konkretno upozorenja za kamere,onda ispremjesta buttons neki se vide neki ne,dakle samo HUD bi ubacio ali ne mogu naci za tu rezoluciju,480x800 imama ali mi je i ova potrebna pa ako moze mala pomoc.UNAPRED ZAHVALJUJEM
VIP
- Učlanjen(a)
- 23.10.2012
- Poruka
- 1.653
Pozdrav drustvo, podesio sam sve za Igo my way 9.6.7 ali nikako ne znam kako da kreiram neki .exe file ili sta vec, koji bih mogao staviti na gps uredjaju kao putanju koju treba da koristi uredjaj da bi se program za navigaciju pokrenuo. Da li neko zna kako da rijesim ovaj problem?
Član
- Učlanjen(a)
- 03.12.2011
- Poruka
- 131
New Lastun-X7-800-multi 05.11.2014
For reasons of "net" only this time I will post simple branding.
1. Fixed two issues, GLONASS and route_del.
2. Fixed other small bugs ... still are.
3. Depending on the setting of the rooms,
I totally changed this function thus are now only two rooms: Static 2D / 3D and 3D Dynamic. Why so called? because the first room does not use variables in terms of speed, and has only the minimum and maximum distance of 3000 m maximum value gradually move toward the minimum and the second will take the first room but these values will fluctuate between them in terms of speed and will apply only on 3D because it seemed silly to zoom in 2D fluctuate depending on speed. otherwise if you are in 2D for the camera settings are "disable".
For fine adjustment relief I turned off because it can mislead and having negative values. You just need to make settings in the first room, static, and in the second to set values for speed. Simply, after adjust the minimum and maximum values and default value that, if you are static maximum value will be constant up to 3000 m maneuver in Dynamic values will vary depending on the minimum and maximum set speed in this room.
I added a navigation shortcut and overview will be enabled to longclik. The values for the two modes are independent settings, the less speed ....
For a better visualization of variables extra_settings I added an option to use percentages to decimal multiplication rate. maybe there ought to go and over 1, up to 1.5x but there is still time.
Theoretically any resolution can be set to values that are close to what you want, but be careful at high zoom (low in settings) will not be able to set a very high angle, you have to "combines"
LINK:
http://download.lesscro.com/iGO Primo/Skin/Lastun/
For reasons of "net" only this time I will post simple branding.
1. Fixed two issues, GLONASS and route_del.
2. Fixed other small bugs ... still are.
3. Depending on the setting of the rooms,
I totally changed this function thus are now only two rooms: Static 2D / 3D and 3D Dynamic. Why so called? because the first room does not use variables in terms of speed, and has only the minimum and maximum distance of 3000 m maximum value gradually move toward the minimum and the second will take the first room but these values will fluctuate between them in terms of speed and will apply only on 3D because it seemed silly to zoom in 2D fluctuate depending on speed. otherwise if you are in 2D for the camera settings are "disable".
For fine adjustment relief I turned off because it can mislead and having negative values. You just need to make settings in the first room, static, and in the second to set values for speed. Simply, after adjust the minimum and maximum values and default value that, if you are static maximum value will be constant up to 3000 m maneuver in Dynamic values will vary depending on the minimum and maximum set speed in this room.
I added a navigation shortcut and overview will be enabled to longclik. The values for the two modes are independent settings, the less speed ....
For a better visualization of variables extra_settings I added an option to use percentages to decimal multiplication rate. maybe there ought to go and over 1, up to 1.5x but there is still time.
Theoretically any resolution can be set to values that are close to what you want, but be careful at high zoom (low in settings) will not be able to set a very high angle, you have to "combines"
LINK:
http://download.lesscro.com/iGO Primo/Skin/Lastun/
Poslednja izmena:
