iGO - bitna podešavanja

Član
Učlanjen(a)
15.04.2011
Poruka
1.374
Video sam da je jedan kolega sa foruma predložio da se pokrene tema gde bi se ostavljala bitna podešavanja i trikovi za iGO pa bih ja sa vama podelio neke koje ja imam. Možda će biti korisno da se takve stvari nađu u jednoj temi zbog preglednosti i da se pišu samo konkretne stvari, cake i fore, a ne da se chat-uje.

Samo da napomenem da se na ovaj način ne želim kititi tuđim perjem i hvaliti tuđim znanjem, već želim da objedinim na jednom mestu sve ono korisno i bitno što su vrhunski znalci postavljali n drugim forumima koje ja posećujem i ovom prilikom im se ZAHVALJUJEM NA TOME ŠTO SU SVE OVO NESEBIČNO PODELILI SA NAMA.
 
Poslednja izmena:
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
HTML:
SYS.txt   PODEŠAVANJE

[Navigation]
junction_view_blink_time = 1000; (0) lines showing the direction of travel in the JV blink at 1 sec

junction_view_blink_time_no_lane = 1000; (0) lines showing the direction of travel in the JV blink at 1 sec

[GPS]
set_messages = 0 so that primo correctly shows the status of the satellite (and not 0/0)

[interface]
exit_on_restart = 0

shutdown_time = 0 does not turn off the device when power is removed

[3d]
planned_route_contour_width = 8 width of the road at a given route, the default is quite thin

[map]
3dcarsizemin = 10000 3dcarsizemax = 15000 = 25000 3dcarsizemul change the size of the cursor

[Interface]
show_mapchanger = 1, no entry or 0 - hides mapchanger 1 - shows it.

show_minimize = 1, no entry or 0 - hides the option to minimize, 1 - shows it.

show_exit = 1, no entry or 0 - hides the button off 1 - shows it.

shutdown_time = 0; time in seconds for automatic sleep mode when power is removed

[2d]
show_guidance_strip = 1  Shows the maneuver arrow on the map in 2D mode

[3D]
planned_route_visible_behind_mountains = 1; (0)   Shows / hides the translucent route, if it covers the terrain (eg, the top)

[Sound.announcer]
gps_signal_lost = 1, (0)

gps_disconnected = 1, (0)

Recalculate = 1, (0)
Enable / disable voice informed (by Agatka) the loss of GPS signal, the receiver gps disconnected and the conversion of the route, if we depart from

[Route]
allow_save_route = 1   Enables auto-saving route. With this option enabled, the navigation is turned off and turn it on again (when navigating), the program will automatically load the last route and will continue to navigate it. Useful for example if somebody falls battery, or suddenly turns off navigation while driving

[Debug]
show_oneway = 1; (0)    Shows / hides the direction arrows on one-way streets

[3d]
planned_route_contour_width = 8
width of the road at a given route, the default is quite thin  refers to the width of the contour set route

[3d]
planned route track width = 5 width of the road at a given route can be wrong, but the greatest value that the program assumes it's probably 5

[Feature]
back_button = 0 (or 1)  adds / removes the BACK button in the interface Primo

[other]
demo_enabled = 0 Hides the DEMO button

[GPS]
default_latitude = xx.yyyyyy
default_longitude = xx.yyyyyy

When you first start igo, or after removing the folder to save the map will open at the location indicated by these has just coordinates. The default is a city in Germany. You can set this entry, eg own home.
Useful for those who are doing something and remove SAVE. I do not have to run every time the cloud to hail a GPS signal and be able to simulate such route. Coordinates of where we can find the options in GPS progranmie


[folders]
has_secondary_root=0
maps="..\..\navigator\content\map"
buildings="..\..\navigator\content\building"
poi="..\..\navigator\content\poi"
dem="..\..\navigator\content\dem"

Enables you to have one set of maps, files, buildings, and single file poi dem despite having two versions of iGO on one card.
sys.txt Section paste the version in which you DO NOT HAVE maps. paths listed above are exemplary!! found and the version of iGO which loaded the above files are located in the Navigator directly on the card, while the version without a map is in a different folder (any) named also directly on the card.


[camera]
maxdistance = 1000; maximum distance

[camera1]

[camera11]

[camera2]

[camera21]

[camera3]

[camera31]
In these sections the same as the entries in the [camera]

[camera.roundabout]
enabled = 0 centery = 20 concerns the behavior of the arrow cursor on the roundabout: 1 - picture roundabout stopped, and the arrow "passes" the roundabout, 0 - arrow indicates the top, while the roundabout on the screen rotates.

[camera.intersection_zoom]
enabled = 1 Zooming in on junctions

[device]
type = "auro2s" info_names = "auro2s" Recognition software and name of navigation, for which it is intended sys.txt

[debug]
skip_eula = 1; omits the display window of the software license

show_oneway = 1; shows / hides (1/0) direction arrow traffic on one-way streets

show_oneway_3d = 1; 0 as above but in 3D mode

show_arrows_on_route = 1, it starts showing arrows on the route

show_lane_info = 1; includes arrays lane

experimental_features = 1; provides access to additional settings

disablesmartdetour = 0; enables the calculation of detours

tmc_provider_list_plus = 1, includes a list of suppliers TMC

skindebug = 0; enables debugging features a skin

showsuspendmessage = 0, and return from sleep "

usenightmode_tunel = 1; switched to night mode in tunnels

show_battery_percent = 1; shows the percentage of battery charge ; log_1 = "\ Storage Card \ igo8_primo \ _debug.log :: 5 'integration to create a log file for tts etc and the path to that file ..

tmc_all_stations = 1; (0) shows all the stations tmc

hnr = 1, (1) enables the use of *. hnr, in the [route] to set the minimum length of the route for which you want to use *. hnr

show_junction_view = 1; includes views of junctions (0) - the settings in the config file \ junctionview.ini show_gps_pos = 1; toggles gps exact position on the map - dot

show_signpost = 1 , it starts showing signs

[dynamiccompressor]
compressor = 1 a0 = 56806 THRs = 24703 ratio = 8 gain = 12 Agata is a little quieter than the standard voices, the podgłośnieniu other sounds are too loud for example, clicking, etc. Da somehow loudness same Agata, you can experiment.

[feature]
back_button = 0 adds / removes (0/1) BACK button in the interface Primo

[feature]
signpost_coloring = 1 To primo kolorowało boards signs

[folders]
sdcardpath = "\ SDMMC \ Primo" Recognition of the media and the root folder [folders ] has_secondary_root = 0 option blocking search by program maps and other components outside of the folder in which the application - useful if on one card you have two or more versions of iGO - each uses its own folder \ content

[gps]
protocol = "NMEA" (in older versions) com_port = 1; dedicated number. port in the device

com_port_speed = 9600 set_messages = 0 so that primo shows correctly the status of the satellites (and not 0/0)

default_latitude = xx.yyyyyy, after removing the folder to save the map will open at the location indicated by the coordinates xx.yyyyyy

default_longitude = j / in this entry can be set for example, own a home, Useful for those who are doing something and remove SAVE. I do not have to run every time the cloud to catch GPS signal, and can for example simulate route

com_port_speed = 9600 clock frequency signal 4800 (the lowest) is a stable signal reception and "slow" moves the cursor / pointer over the map, sometimes delay the progress of the cursor traveled road about a dozen or a few dozen meters. too high frequency causes disconnects / signal - but closer to the actual cursor position of the car to display on the map. Experiment: 4800, 9600, 19200, 38400, etc. equipment manufacturers (sewn GPS) provide the most favorable frequency clock. you have to remember to change the parameter in data.zip / config / devices / *. ini file (own urządz.navi)

[interface]
exit_on_restart = 0 disables the device when power is removed shutdown_time = 0 disables the device when power is removed show_exit = 1 extra_settings = 1

mapfontscale = 150; (100/100%) Enlarge / Reduce font size names (streets, village, etc.) resolution_dir = "800_480" parameters navi native resolution vga = 0

[Itiner]
pass_via_distance = 1000 option is useful when the route of via points. Navigation does not lead us directly by point through but chooses the best route for the purpose of recognizing that we have reached a point "by" if we got him at a distance of not more than (for example 1,000 meters).

[map]
3dcarsizemin = 10000 minimum size 3dcarsizemax = 15000 maximum size 3dcarsizemul = 25000 resizing cursor speedcam_visibility = 2000 visibility settings size of map elements

[Mapchanger]
map_ta = "TeleAtlas" map_nt = "NAVTEQ" map_ot = "OTHER" To name changer suppliers maps were displayed correctly

[navigation]
env_zone_warning_distance = 500 Distance warning of the environmental zone as Germany (in the example 500 to activate the search in google poi in primo 2.4. [other] demo_enabled = 0 Hides the DEMO

[other.fm_transmitter]
fmtx_enabled = 0 Enable transmitter settings for the FM transmitter

[rawdisplay]
res = 0 screen_x = 800 screen_y = 480 resolution devices navi

[route]
allow_save_route = 1

hnr_ignored_missing_country_ids = * 1 line, enables automatic recording of the route. With activated option = 1, after turning off navigation and turn it on again ( while navigating), the program will automatically load the last route and will continue to navigate it. Useful, for example, if someone falls battery, or suddenly turns off navigation while driving. 2 line, a listing allows you to share files *. hnr (predefined route), even if you do not have a set Primo " brand = "Nav N Go" product_brand = "Nav N Go" product_model = "iGO Primo" naviextras_silent = 1, for users registered with legitimate software and want all this additional internet services such as local alarm points, points poi suppliers, etc. .

[sound]
lua_voice_enabled = 1 entry format activating voices "lua" - applies only to Primo 1.1 (Primo 1.2 and 2.x by default supports "lua" so this entry is not needed)

[sound]
csv_voice_enabled = 1 For use with Primo 1.2 or 2.x votes other than "lua" to prevent the appearance of the message "Unsuported voice files" and also get support for votes in "csv" file to add to the sys.txt entry is not required if all the voices in the \ Primo \ content \ voice in the format of "lua"

[sound]
csv_voice_enabled = 1 If the dialog box does not agates are in the directory content \ voice does not have the file: Voice_TTS-nua-plp-f1-dri40-vssq5f22.zip. in sys.txt must be p / w entry.

[sound]
os_volume = "255" sound_volume = "255" voice_volume = "255" maximum volume setting 0-255

[sound]
; os_volume = "255" ; sound_volume = "255" ; voice_volume = " 255 " Custom / dedicated device / volume setting every time you turn Example of message about the conversion route - Agata

[speedcam]
disable = "_SUI", "_GER", "_AUT" Disabling warnings about the radars in the countries where it is prohibited. In the example Switzerland, Germany, Austria.

[tmc]
source = " gnsport "source , The waiting time in seconds TMC for dial tone before continuing the search

hold_station_time = 15; waiting time in seconds at the frequency of the station, after the loss of a signal to operate the TMC messages

[tmc-http]
enabled = 1 1 - tmc function enabled by the internet. start = 1 1 - download events at run iGO servers.size = 1 1 - use the following data server tmc servers

[0]. url = "http://zippy.naviextras.com/services/tmclite/data/nng-igo-tmc-iphone/ 0 / "login to the servers. dl_dist_0_km = 50.0, consider the events at a distance (for example 50 km) dt_dl_0 = 60.0 refresh messages which (in the example 60 = 2 entry only when using TTS voices to iGO_Primo Agata Suggested entry for both the Primo 1.x and 2.x - it is not required, but forces the program priority pronouncing street names instead of numbers roads, TTS voices gives a higher priority in the system, etc. .. Description of function:

[tts]
always_say_road_names = 1 1 - pronounced road number, 2 - pronounce the name of the street, 3 - pronounced number and the name of the road if occur. use the "always_say_road_names = 2 or 3", can not be combined with: skip_road_numbers = 1 skip_exit_numbers = 1 1 = skip exit number

skip_road_numbers = 1 1 = skip road number (when present together with the name of the street)

announce_exit_directions = 1 1 = at the exit from the highway exit number pronounced.

[utility]
calibratefix = 1 Calibration Safety camera alerts distance 1 line, warning against radar: = 0 disabled, 1 = warn if exceeded; = 2 when approaching 2 ruler, currently the limitation of distance (speed in km / h / distance in meters) of the risks 3 line, a signal approach to the distance of the camera = 300 4 line, the signal reaching the section = 200 5 line, the distance to the zone of action of the camera = 100 6 line, the maximum information about the camera ahead = 300 II. Configuration views / objects on the map

[2d]
show_guidance_strip = 1 and shows the maneuver arrow on the map in 2D mode. (invisible by default)

minzoom2d = 200; larger minimum maxzoom2d = 1500; maximum magnification defaultzoom2d = 1200; default zoom

overview_zoom2d = 7500; larger when viewing label_rendering_order = 1, (0) the inclusion of rendering labels ( text, screen, icon)

building_draw_outline = 1; (0) enables outline of buildings

building_maxzoomlevel = 500, (500) the maximum magnification of buildings

draw_polygon_contours = 0; (1) drawing Solids buildings

drop_little_road_segments = 1; (0) show short segments of roads

show_planned_route_arrows = 1 , (1) the arrows showing the planned route

road_simplification_level = 5, (5) the level of simplification displaying the

adaptive_2d = 1; (1) adaptation of 2D

group_poi_icons = 0; (1) grouping objects POI

max_icons_shown = 20, (30) the maximum number of display objects

enable_icon_fight = 1; (0) toggles the icons above the map

traffic_lights = 1; (0) showing traffic lights

mincarsize = 80, () the minimum size of the cursor

mincarsize_zoomlevel = 2000; minimal enlargement of the cursor

maxcarsize = 150; () maximum magnification cursor

maxcarsize_zoomlevel = 200, the maximum size of the zoom level min2dplannedroutewidth = 5, (5) the minimum width of the road

[3d]
stereo_projection = 1 ; option activates the 3 dimensional view of the map window - you need 3D glasses (red / blue)

disable_roadsign_navigation_mode = 0 , change the display names of streets 0 = street names in balloons, 1 = names of streets "on the streets" planned_route_contour_width = 8 , width of the road at a given route, the default is quite thin (apparently the maximum permissible value is = 5, you need to check.

planned_route_visible_behind_mountains = 1 ; shows / hides (1 / 0) translucent route if it obscures the terrain (eg mountain)

[3d]
minzoom = 75; larger minimum maxzoom = 200; maximum magnification minangle = 40; minimum angle

maxangle = 55; maximum angle defaultzoom3d = 150; default larger defaultangle = 50; default angle

angleoffset = 10; angle at bringing speedzoom = 0; velocity augmentation speedangle = 1; tilt speed

overview_enabled = 1; zoom and tilt lock overview_distance = 5000; distance and tilt angle changes

overview_zoom3d = 2500; distance changes magnification overview_angle = 70, distance changing the angle

[3d]
roads_as_line_stripes = 1, (1/0) to display roads as the belts

reduce_line_stripes = 1, (0) to reduce respiratory belt line planned_route_track_width = 10, (1/10 ...) belt width Route

planned_route_track_contour_width = 2; (1 / ...) width of the outline

disable_car_normals = 1; blocking cursor size anti_alias_buildings = 0, (0) smoothing Bryl buildings

anti_alias_landmarks = 0, (0) smoothing of 3D objects anti_alias_shapes = 0, (0) smoothing of shapes

landmark_min_brightness = 300, (700) the minimum brightness of 3D objects

max_pois = 60, (97) the maximum number of POIs on the screen

max_pois_on_horizont = 12, (17) the maximum number of POIs on the horizon

use_all_building_textures = 0; (1) texturing Bryl buildings

render_buildings_as_shapes = 0 , (0) 3D buildings flat on the ground - outlines the basics, instead of lumps asymmetric_projection = 0, (0) asymmetric throw

car_antialias_mode = edgeblur; (supersample) edgeblur - smoothing mode cursor

fade_around_cursor = 1; buildings disappear from the map by clicking

fade_distance_for_car = 40; (20) buildings fading in the distance

fade_overlap_tolerance = 50; (32) tolerance disappearance of objects

[3d_config]
disable_roadsign_navigation_mode = 1, 0 = street names in balloons 1 = names of streets "on the streets" roadsign_lines_per_screen = 14, the font size of the names of towns and streets - less value, you know subtitles roadsign_always_framed = 0; balloons with the names of roads only active in navigation mode (0) or also in Review (1) III. speed cameras and other warnings, one of the moderators of the proposed simplified entry Agata:

[speedcam_category: 0]
activated_speech = "Warning! The camera steady. "

[speedcam_category 1]
activated_speech = "Warning! Possible mobile speed camera. "

[speedcam_category 2]
activated_speech = "Warning! Possible roadside inspection. "

[speedcam_category 3]
activated_speech = "The camera medium speed. Episode. "

[speedcam_category 4]
activated_speech = "Speed camera at the traffic light."

[speedcam_category 6]
activated_speech = "Warning! Railway crossing. "

[speedcam_category 7]
activated_speech = "The camera on the bus lane."

[speedcam_category 8]
activated_speech = "Warning! Dangerous place or distance. "

[speedcam_category 9]
activated_speech = "Warning! School Zone. "

[speedcam_category 10]
activated_speech = "we enter the city. Slow down! "

[speedcam_category 11]
activated_speech = "Measuring the speed of traffic lights."

[speedcam_category 12]
activated_speech = "toll collection point."

[speedcam_category 15]
activated_speech = "Zone of charge for entry."

[speedcam_category: 31]
activated_speech = "Warning! Zone of accidents. "

[speedcam_category 4]
activated_speech = "Camera Red świadło. etc.

[speedcam_category: 0]
activated_spoken_type = speech Activation of expression activated_speech = "Speed camera ahead." Speed camera. overspeed_speech = "Reduce your speed." Reduce speed.

[speedcam_category 1]
activated_spoken_type = speech activated_speech = "Mobile speed camera ahead." Mobile speed camera. overspeed_speech = "Reduce your speed."

[speedcam_category 2]
activated_spoken_type = speech activated_speech = "Speed camera ahead." Speed camera. (Permanently attached) overspeed_speech = "Reduce your speed."

[speedcam_category 3]
activated_spoken_type = speech activated_speech = "Average speed camera ahead." Measurement of the average velocity. (Segmental) overspeed_speech = "Reduce your speed."

[speedcam_category 4]
activated_spoken_type = speech activated_speech = "Red light camera ahead." The camera red świadło. overspeed_speech = "Reduce your speed."

[speedcam_category 6]
activated_spoken_type = speech activated_speech = "Railway crossing ahead." Railway crossing. overspeed_speech = "Reduce your speed."

[speedcam_category 7]
activated_spoken_type = speech activated_speech = "Bus lane camera ahead." Lane for buses. overspeed_speech = "Reduce your speed."

[speedcam_category 8]
activated_spoken_type = speech activated_speech = "High accident zone ahead." Zone accidents. overspeed_speech = "Reduce your speed."

[speedcam_category 9]
activated_spoken_type = speech activated_speech = "School Zone Ahead." School.

[speedcam_category 10]
activated_spoken_type = speech activated_speech = "Town entry point ahead." The entrance to the city. overspeed_speech = "Prepare to reduce your speed."

[speedcam_category 11]
activated_spoken_type = speech activated_speech = "Red light and speed camera ahead." Red light and speed camera. overspeed_speech = "Reduce your speed."

[speedcam_category 12]
activated_spoken_type = speech activated_speech = "Toll booth ahead." Point tolls. overspeed_speech = "Prepare to stop."

[speedcam_category 15]
activated_spoken_type = speech activated_speech = "Congestion charge zone ahead." Congestion charge zone. overspeed_speech = "Reduce your speed."

[speedcam_category 16]
activated_spoken_type = speech activated_speech = "Police control zone ahead." Police control zone. overspeed_speech = "Reduce your speed."

[speedcam_category 17]
activated_spoken_type = speech activated_speech = "Mobile speed camera ahead." Mobile radar. overspeed_speech = "Reduce your speed."

[speedcam_category 31]
activated_spoken_type = Speech Activation of expression activated_speech = "Dangerous area ahead." Note dangerous area. overspeed_speech = "Reduce your speed." Reduce speed.














[rawdisplay]

autoconfig=1 It will make iGo work with TouchHD native rotation.
   
class="auto"
   
driver=GX  GDI or GX
   
highres=0
   
screen_x=480
   
screen_y=800
   
stretch=0
   

[interface]

resolution_dir="480_800"

screen_x=480 forces iGo interface to fit in these screen resolutions
   
screen_y=800 Tells the prog the dimension of x & y of the screen,maybe irrelevant if using autoconfig.
   
angleoffset=0
   
autoscroll_on_click=1
   
autotilt_maxzoom3d=1000

autotilt_minzoom3d=40

autotilt=1

default_poi_icon="Contacts" 

defaulttilt3d=75000

defaultzoom2d=1000

defaultzoom3d=40

disable_3dstick_labels=1 

drive_carefully=0

empty_favorites=0

exit_on_restart=0

laneinfo_signpost_enabled=1

mapfontscale=100

maxzoom2d=60000  zoom out level (disabled get you into space O)

minzoom2D=40  zoom in level 2d

minzoomglobe=100000

msgbox_max_width=50

newalignment=1

poi_show_all_btn=1

popup_info=1

recalc_voice=0 Enables route recalculation voice warning

screen_snap_distance=40

show_exit=1  I believe disabling this option would hide the exit button.

show_gps_config=1

show_minimize=1

show_orientation=1

show_timezoneslider=1 

show_tmc_config=1

show_zoombar=1  also see zoomscale_disappearing

showselection=1

shutdown_time=0

skin="ui_igo8"

spec_fav_count=4

theme="skin\igo8_plus.zip"

use_big_lang_flag=1

use_spec_fav=1

vga=1

waypoint_list_ignore_autosource=1

wide=1

Zoom2dpercent=0


    [loading]

    loading_bmp="loading.bmp" defines startup loading background image

    progressbar_bmp="loading_progressbar.bmp" defines the progress bar image

    progressbar_x=40 sets progress bar horizontal position on screen

    progressbar_y=556 sets progress bar vertical position on screen

    show_progressbar=1 enables progess bar during startup

    show_statustext=0 enables loading status messages during startup

    supress_highway_enter=0

    supress_straight=0

    supress_trivial_left=0

    supress_trivial_right=0

    text_align=1 Left=0,Center=1,Right=2 and Justify=3

    text_fontcolor=xFFFFFF

    text_fontsize=30

    text_w=600

    text_x=100

    text_y=400

    traincrossing=1

   

    [phone]

    driver="TAPI"

    exe_path="\Windows\cprog.exe"

    win_name="Phone"

   

    [poi]

    enable_pois_before_080217=1 080217 is the date can be changed as needed

    multipoi=1 allows you to use more than one set of POIs at a time (will show duplicates though)

   

    [usb]

    disable_on_startup=0

    enable_on_shutdown=1

    quitmap_msg_quits=0

   

    [speedcam]

    disable="_SUI", "_GER", "_AUT"

    enable_at_startup=1

    speedcam_sound="!alert1"

    usemio=-12,90,37,27

   

    [route]

    allow_carpool=0

    allow_charge=1

    allow_ferry=1

    allow_highway=1

    allow_special=0

    allow_unpaved=0

    allow_uturn=1

    correctness=80  we used to have a slider for that

    cross_border_routes=1

    fast_car_multiplactor=0

    fast_car_speed=0

    motorcycle_multiplactor=0

    motorcycle_speed=0

    planned_route_weight=7

    route_type="ECO"

    scenic_highway_weight=4

    scenic_scenic_weight=2

    slow_car_multiplactor=0

    slow_car_speed=0

    tmc_weight=6

    vehicle_type="truck"

   

    [feature]

    signpost_coloring=1

    text_guidance=1

    tmc_event_coloring=1

    tmc_traffic_side=1

   

    [mydata]

    favicon=""

    max_favorites=16

    max_histories=40

    num_favicons=7

   

    [mydata.tracks]

    auto_track_visible=1

    record_auto_track=0

    tracklog_folder=""

   

    [warning]

    approach_beep_distances=200

    approach_beep_sound="!sectionbeepB"

    max_section_time=240

    overspeed_sound= "!alert3"  speedcam sound

    pedestrian_warning_threshold=10

    pedestrian_warning=0

    section_beep_distance=200

    section_beep_sound= "!sectionbeepA"

    section_end_sound= "!sectionend"

    section_start_sound="!sectionstartA"

    speedcam_max_angle=20

    speedcam_max_lookahead=400

    speedcam_maxdistance_from_road=0

    speedcam_snap_distance=200

    speedcam_soundtype=1

    speedcam_visualtype=1

    speedcam_warning=1

    speedlimit_warning_visual=1

    speedlimit_warning_voice=1

    speedlimit_warning=1

    speedwarn_alt_builtup_based=1

    speedwarn_alt_limit=1

    speedwarn_alt_tolerance=0

    speedwarn_alt_toltype=0

    speedwarn_tolerance=110

    speedwarn_toltype=0

    warn_distances=130:450,110:350,90:300,60:200,40:10 0 These numbers are apparently in the format of Speed:Distance.

   

    [itiner]

    show_only_ahead_of_car=1

   

    [kml]

    default_icon=1

   

    [map]

    2dheadup=1 Will keep the road ahead always pointing to the top of the screen

    3d_brunnel_shutdown=0

    3d_buildings_distance=0

    3d_buildings=1

    3d_dem_detail=2

    3d_dem=1

    3d_landmarks=1

    3d_max_tiltlevel=7500

    3d_max_zfar=1000

    3d_max_zoomlevel=4000

    3d_min_zoomlevel=60

    3d_roads=1

    3d_scale_carmodel=1

    3d_tunnels=1

    3dcarsizemax=10000

    3dcarsizemin=5000

    3dcarsizemul=30000

    alternative_roadnames=0

    auto_nightmode=0 Stops the prog switching to nightmode automatically

    cross_border_routes=1

    follow_gps=1

    inertia_on_map_move=1  sets autoscroll on the map, tends to be buggy though sometimes doesn't stop.

    map_mode="3D"

    maxFovRatioForPoly=8

    maxPolyDistances0 = 2000

    maxPolyDistances1 = 3000

    maxPolyDistances2 = 4000

    maxPolyDistances3 = 5000

    maxTrackDistances0 = 2500

    maxTrackDistances1 = 3500

    maxTrackDistances2 = 4500

    maxTrackDistances3 = 5500

    minPolyDistances0 = 500

    minPolyDistances1 = 500

    minPolyDistances2 = 500

    minPolyDistances3 = 500

    minTrackDistances0 = 500

    minTrackDistances1 = 500

    minTrackDistances2 = 500

    minTrackDistances3 = 500

    roadblockicon_maxzoom=2000

    rotation=0

    shields=1

    show_labels=1 

    show_oneway=1  turns on or off the arrows showing one way streets

    stop_rotate_on_map_move=1

    terrain_in_2d=0

    textured_poly=1

    viewpreset_front1="30,100,7200,10"

    viewpreset_front2="140,7000,6000,10"

    viewpreset_front3="140,7000,6000,10"

    viewpreset_top="600,50000,225,10"

    zoomscale_disappearing=1  works with show_zoombar

   

    [tripcomputer]

    num_of_trips=4  default igo8 has only 3

   

    [debug]

    autosave=1

    bringtotop_afterresume=1

    buildneworderlist=1

    cache=2048

    compass_type=2

    disable_3d=0 disables 3d buildings and roads

    disable_outlookpoi=1 stops iGo from turning your contacts into POIs.

    double_pixel_mode=2 3d mode fastdraw

    doublepixel_stable_frame_time=500 time in ms before leavin fastdraw

    earth=1

    enable_buildings=0

    enable_landmark_occlusion=1

    enable_roadshow=1

    enable_roadsign=1

    fov=40

    gnome_dem_files=1

    hide_itiner_crossing=1

    join_dual=0

    lang_registry_2006=1

    loop_sim=0

    max_memory=8388608  might've caused an error

    mute_os_key=1  a value of 1 mutes the click noise from the OS when touching a touchscreen

    no_file_cache=0

    nortc=0  RTC = real time clock aka the devices internal clock

    pin_sets_start=1

    poi_labels=1

    raster_quality=1

    replay_tmc=1

    reserve_memory=2097152

    run_on_mio_mantas=1

    screen_calibration=1

    show_arrows_on_route=1  little arrows in direction of route

    show_device_type=0

    show_gps_pos=1  this works again O)

    show_lane_info=0

    show_ltn=1

    show_multinode_maneuvers=1

    show_oneway_3d=1 3d arrows in the direction of travel on one way streets

    show_oneway=1 Will either show on not show one way streets.

    show_pedestrian=1

    show_performance=1  cpu / mem / whatever bars on top of screen

    show_plural=1

    show_poi_areas=1

    show_poi_boundingrects=1

    show_priority_maneuvers=1

    show_prohibited_maneuvers=0

    show_rawdisplay_info=1  handy for seeing what igo chooses as display driver

    show_residentonly=0

    show_signpost=1

    show_speed_limit=1 Will show the speed limit road sign on the corner of the screen

    show_turn_penalty=1

    sim_speed_factor_max=8.0

    skip_eula=1 skips the End User License Agreement at start-up (only happens on first run anyways)

    slowsim=1

    smart_2d=1

    sound_q_length=200

    speedcam_enabled=1

    split_dual=0

    strap_waypoints=1

    supress_highway_enter=0

    supress_straight=0

    supress_trivial_left=0

    supress_trivial_right=0

    tmc_all_stations=1

    topmost=1

    traincrossing=1

    tts_expected_engine_delay=1400

    tts_getaway_time=200

    tts_min_ready_wav=1

   

    [defaults]

    mainroadness=60

    shortessness=50

    simplificationness=40

   

    [gps]

    background_navigation=1

    baud=57600

    default_longitude=2.294760 starting postion on the map before GPS is found.

    disable_advanced=0

    logging=0  see also mydata.tracks

    port=4

    source="nmea"

   

    [tts]

    always_say_road_names=1

    announce_exit_directions=1

    announce_street_name=1

    priority="HIGH"

    skip_exit_numbers=0

    supress_trivial_left=1

    supress_trivial_right=1

    traincrossing=1

    tts_buffer=131072

    tts_logics=3

   

    [local]

     Date Format: To select your desired format, delete the  infront of the format you want and  in front of the rest (or
just delete all of the other lines)

     Dateformat = 0 YYYY-MM-DD

     Dateformat = 1 AAAA.MM.GG

     Dateformat = 11 MM / DD / YYYY

     Dateformat = 2 YYYY / MM / DD (DEFAULT)

     Dateformat = 3 YYYY-MM-DD

     Dateformat = 4 AAAA.GG.MM

     Dateformat = 5 YYYY / MM / DD

     Dateformat = 6 DD-MM-YYYY

     Dateformat = 7 DD.MM.YYYY

     Dateformat = 8 DD / MM / YYYY

     Dateformat = 9 MM-DD-YYYY

     Dateformat = 10 MM.GG.AAAA

   

    [msnd]

    enabled=0

    msnd.start=0

   

    [sound]

    auto_mute=0

    device_bps=128000

    device_samplerate=44100

    device_stereo=1

    ding=0

    dynamic_volume_maxspeed=100

    dynamic_volume_minspeed=40

    dynamic_volume_os_volume_max=255

    dynamic_volume_type=1

    dynamic_volume_voice_volume_max=100

    dynamic_volume_voicemaxspeed=80

    incomingcallsetting=1

    mute_os_key=1

    queue_length=200

    sound_muted=0

    sound_q_length=200

    sound_volume=255

    suspend_time=5 timeout for wavedev to goto sleep

    use_os_volume=0

    voice_muted=0

    voice_volume=255

   

    [navigation]

    autoreplan_action="AUTO"

    gps_pos_to_road=1

    show_countrychange=1

    show_current_city=0

    sim_speed_factor=1.0 Determines how fast the simulation runs, 1=realtime

    skip_grab_viewchanging=1

   

    [2d]

    guidancearrow_disappearlevel=600

    guidancearrow_maxshift=12

    maxguidancearrowsize_zoomlevel=0

    maxguidancearrowsize=65

    minguidancearrowsize_zoomlevel=1200

    minguidancearrowsize=40

   

    [3d]

    3d_tmc_road_extra_width=200 

    building_camera_distance_far=500

    building_camera_distance_medium=50

    building_camera_distance_near=10

    disable_3d_labels=0 

    fade_distance_for_car=50

    fade_distance_for_guidance_arrow=500

    guidancearrow_contour=0

    guidancearrow_first_alpha=24  transp of 1st arrow

    guidancearrow_first_size=1.1  scale of 1st arrow

    guidancearrow_second_alpha=12

    guidancearrow_second_size=0.8

    guidancearrow_skew=0 

    guidancearrow_thickness=0 

    guidancearrow_width=0 

    guidancearrow_zoomfactor=0 

    max_poly_distance_lower=0

    max_poly_distance_upper=0

    max_poly_segments_shown=0

    max_poly_segments_shown_1=400

    max_track_distance_lower=0

    max_track_distance_upper=0

    max_track_segments_shown=0

    min_poly_distance=0

    min_poly_segments_shown=0

    min_poly_segments_shown_1=200

    min_track_distance=0

    min_track_screen_ratio=0

    min_track_segments_shown=0

    road_clip_plane_camera_delta=50   

    road_clip_plane_to_camera_height=0 

    roadsign_lines_per_screen=24

    rotated_roadsigns=1

    show_guidance_arrows=1

    show_guidance_strip=1

    track_screen_ratio=0

    use_all_building_textures=0  not?

   

    [tmc]

    announce_total_route=1

    auto_detour_calc=0

    baud=38400

    ignore_all_events=0

    port="COM,3"

    saved_config_available="1"

    saved_config_classname="RDS_GPSTMC_SILICONLAB"

    saved_config_port="3"

    saved_config_portname="COM"

    saved_last_tuning_mode="1"

    source="gns"

   

    [timezone]

    reset_os_timezone=0

    sync_os_timezone=0

    auto_index=29

    default_timezone=29  GMT+1 amsterdam

    index=29

    manual_dst=0

    reset_os_timezone=0

    sync_os_timezone=0

    sync_time=1

    use_auto=1

   

    [power]

    backlight_day=100

    backlight_night=10

    backlight_slow_api=1

    backlight_sync_with_OS=0

    battery_warning_limit=20

    power_off_mode=1

    power_off_timeout=300

    powermgm_state=0

    skip_resume_process=1

    skip_suspend_process=1

   

    [smartzoom]

    auto_follow_on=1

    auto_follow_time=10

    auto_smartzoom_time=8

    autozoom_address=100

    autozoom_coord=200

    autozoom_cos=200

    default_visibility_altitude=4000

    enabled=1

    enabled2d=1

    maxangle=90

    maxzoom=300

    minangle=0

    minangle=8

    minzoom=55

    overview_distance=20000

    overview_zoomlevel=1000

    overview=0

    restore_smartzoom_on=0

    use2d=1 use2d is to use separate smartzoom for 2d and 3d. Once this is implemented in a UI it should be set to 1.

    zoom_after_find=1

   

    [screen]

    current_background="Carbon.bmp"

    focus_activator_key=""

    focus_color=""

    focus_followlinks=""

    focus_halign=""

    focus_list_keydown=""

    focus_list_keyleft=""

    focus_list_keyright=""

    focus_list_keyup=""

    focus_list_move_before_scroll=""

    focus_sprite=""

    focus_type=2

    focus_valign="" 


    focus=1
    menu_animation=1

    nightmode=0

   

    [3d_config]

    disable_roadsign_navigation_mode=1

    roadsign_lines_per_screen=24

    rotated_roadsigns=1

   

    [bluetooth]

    send_showphoneui_on_dial=1

   

    [config]

    autoset2donmap=1

    autoset3doncockpit=1

    hideroadaltname=1

    overspeedrewarnbelow=1


    SafeModeMinSpeed=40

   

    [other]

    demo_mode=1

   

    [settings]

    accident_map=1

    accident_panel=1

    accident_recalc=0

    closed_map=1

    closed_panel=1

    closed_recalc=0

    closures_map=1

    closures_panel=1

    closures_recalc=0

    congestion_map=1

    congestion_panel=1

    congestion_recalc=0

    danger_map=1

    danger_panel=1

    danger_recalc=0

    heavy_map=1

    heavy_panel=1

    heavy_recalc=0

    invalid_map=1

    invalid_panel=1

    invalid_recalc=0

    police_map=1

    police_panel=1

    police_recalc=0

    roadworks_map=1

    roadworks_panel=1

    roadworks_recalc=0

    weather_map=1

    weather_panel=1

    weather_recalc=0






















POI     

picturepoi_show_all_containers = 0; icon does not display photos on your desktop, like poi point, but in the "Search> More> Image" you can find it.

picturepoi_has_mypicturepoi = 0; Primo does not load images as poi at all





This allows you to specify a period of time where an alert or speedcam is in/or not in use.


[warning]
warning_time_intervals="mo-tu|6:00-22:00"   (this is for all alerts)

warning_time_intervals="mo-fr|6:00-12:00,th-fr|16:00-22:00"  (for split timings, say for example a school zone)

This covers one specific category/type

[speedcam_category:1]
warning_time_intervals="mo-fr|6:00-23:00"
[speedcam_category:2]
warning_time_intervals="sa-sa|6:00-22:00,su-su|6:00-22:00"



This only makes the pois show at a specific range

Default for all is 500 meters, but you can overide all other category/types by adding the category and meters.

[speedcams]
speedcam_default_visibility = 500
speedcam_category_visibility = 1,1000
speedcam_category_visibility = 18,400
speedcam_category_visibility = 19,300


Useful for android phones with not much memory where some content (e.g. maps) must be held on a removable SDCard

[folders]
content=%SDCARD%/external_sd/iGO/content    ;Directs iGO to "content" directory on external SD card (folder name correct for Samsung Galaxy Ace 2 on Android 2.3)
content=/mnt/extSdCard/iGO/content        ;Directs iGO to "content" directory on external SD card (folder name correct for Samsung Galaxy Ace 2 on Android 4.1)


[map]
no_road_rotate_speed_min=2; speed at which map rotates when changing direction in track up mode while offroad,default is 10.

[rawdisplay]
class="landscape"; resolution displayed as widescreen view like 800x480, 480x272.
class="portrait"; resolution displayed as height greater than width like 480x800 etc.

The 3 lines under interface below force igo8 to display as a full 800x480 on an 800x480 device by using the 800_480 directory in data.zip, instead of doubling the size of 400_240 directory's images in data.zip to suit an 800x480 device like mine did when I first got it.
[interface]
vga=0
skin="ui_igo8"
resolution_dir="800_480"
 
Poslednja izmena:
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
KML PRETRAGA - PODEŠAVANJE U sys.txt

Potrebno je u sys.txt ubaciti..


[address.multi]
allow_empty_categories=1
search_priority="history;favourites;street;location;poi_container;kmlpoi;poi;gls"
ewentualnie jeszcze:

[poi]
kml_as_logical_provider=1
 

Prilozi

  • SLIKA.jpg
    SLIKA.jpg
    65,4 KB · Pregleda: 251
Poslednja izmena:
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
kada se stave ; (tačka i zarez) ispred nekog teksta u sys.txt to znaci da je to iskljuceno
i da ne radi, a kada bi se obrisala tačka i zarez ispred teksta onda bi ta opcija bila aktivna

PRIMER:

[rawdisplay]
force_renderer="RENDER_MOYA"
driver="engine"
screen_xy="auto"
;use this entries for full HD and QHD:
;highres=1
;driver="gdi"

 
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
ZNAČENJE SVIH EKSTENZIJA KADA SU MAPE U PITANJU:


HTML:
Files in directory \content\building:[/COLOR][/COLOR]
[COLOR=#ff0000][COLOR=#0000b3]
*.3DL - 3D image of landmarks
*.3DC - 3D image of buildings
*_petrol.3DL - 3D image of petrol stations
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\car:
*.ZIP - contains the 3D model of the vehicles
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\dem:
*.DEM - Contains digital model of the relief
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\global_cfg:
global_cfg.zip - Global configuration of countries (country information)
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\histspeed:
*.HSP - average data for the congestion on the roads in different days of week and time of day. Helps in calculating the route to avoid potential congestion. Do not be confused with TMC (he is in real time)!
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\TUTORIAL:
*.ZIP - contains files with tutorial for the program in different languages
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\map:
*.HNR - Base with prepared routes (4 types: Fast, Short, Easy and Economical) for Eastern and Western Europe, helping to speed the calculation of long routes. To work is needed all maps of the corresponding region to be available.
*.FDA - Driver Alerts - show active driver alerts (signs)
*.FTR - Truck Information - this information is used to calculate the truck routes and can avoid passing trough road prohibited for trucks
*.FPA - Point Addressing - it contains data for the real addressing points, where the address is not on the road
*.FBL - the maps of countries.
*.FSP - speed profile for a given road for smart routes
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\phoneme:
*.PH - speaks of street names
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\POI:
*.POI - Point of Interest
*_3dlm.poi - 3D images of POI, they can be selected from the menu
*_truck.poi - Parkings, service and so on for trucks
*_DKV_rich.poi - Places which works with DKV card
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\speedcam:
*.TXT, *.SPC - contains files with points of speed cameras and/or police radars
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Files in directory \content\USERDATA:
POI - contains files with user points of interest, usually in .kml format
USERICON - contains files with user icons of POIs, usually in .bmp format
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/building:
*.3DL - 3D slike znamenitosti
*.3DC - 3D slike zgrada
*_petrol.3DL - 3D slike benzinskih stanica
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/car:
*.ZIP - 3D modeli automobila
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/dem:
*.DEM - digitalni model reljefa (brda i planine)
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/global_cfg:
global_cfg.zip - podaci o zemlji, saobraćajni propisi
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/histspeed:
*.HSP - prosečni podaci o gužvi na putevima u različito doba dana. Pomaže u izračunavanju rute
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/TUTORIAL:
*.ZIP - tutorial za korištenje navigacije na raznim jezicima
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/map:
*.HNR - Baza pripremljenih ruta (4 tipa: Brzi, kratki, laki i ekonomični). Pomaže u izračunavanju trajanja rute.
*.FDA - Upozorenja za vozača - prikaz aktivnih upozorenja(znakova)
*.FTR - Informacije za kamione - koristi se kod izračunavanja rute za kamione(da se izbegnu putevi gde je kamionima zabranjeno i slično)
*.FPA - Adresiranje - adrese ulica
*.FBL - mape
*.FSP - profil brzine datog puta za pametna rutiranja
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/phoneme:
*.PH - govori imena ulica
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/POI:
*.POI - Point of Interest(razne zanimljivosti, restorani, barovi, aktivnosti, i slične stvari)
*_3dlm.poi - 3D slike POI-a
*_truck.poi - parking, servis i ostale usluge za kamione
*_DKV_rich.poi - mesta koja rade s DKV karticom(kartica za gorivo za privredni teretni i autobusni promet)

.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/speedcam:
*.TXT, *.SPC - mesta gde se meri brzina/policijskih radara
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Podaci unutar sd/iGO/content/USERDATA:
POI - podaci o ličnim zanimljivostima, obično u .kml formatu
USERICON - lične ikone(slike) POI-a, obično u .bmp formatu
.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,
Ko ne koristi mapchanger neka ručno preimenuje foldere
za korišćenje NAVTEQ mapa preimenovati foldere
building ---> building_OT
histspeed ---> ne mora ako se ne koristi
map ---> map_OT
phoneme ---> ne mora ako se ne koristi
poi ---> poi_OT

building_NT ---> building
histspeed_NT ---> ne mora ako se ne koristi
map_NT ---> map
phoneme_NT ---> ne mora ako se ne koristi
poi_NT ---> poi

Za korišćenje TOPMAP(topmap+tomtom) mapa preimenovati (posle korišćenja NAVTEQ mapa) foldere

building ---> building_NT (android _NQ)
map ---> map_NT (android _NQ)
poi ---> poi_NT (android _NQ)

building_OT ---> building
map_OT ---> map
poi_OT ---> poi

Za korišćenje samo TOM TOM mapa preimenovati (posle korišćenja topmap mapa) foldere

building ---> building_OT
map ---> map_OT
poi ---> poi_OT

building_TT ---> building
map_TT ---> map
poi_TT ---> poi
 
Poslednja izmena:
Učlanjen(a)
09.10.2011
Poruka
274
Bravo za temu! Mislim da sam i sam vise puta sugerisao na neke stvari koje mogu da uticu na bolju funkcionalnost ove navigacije. Konkretno, broj licenci, koje mogu da se svedu na pristojnu meru, iako sada postoje verzije koje su full patched, ipak ima i onih (AvicSync) koje jos uvek nemaju tranje licence, zatim broj ux dodataka i njihovo znacenje u samom podesavanju programa i kao najvaznije sys.txt koji u velikoj meri utice na izgled i funkcionalnost same navigacije. Mnogo razlicitih sys.txt sam video sa razlicitim opcijama setovanja i razlicitim komandama. Siguran sam da su mnoge stvari bitne, ali i da ima dosta suvisnih stvari. I ja sam kombinovao i prepravljao iste i trudio se da izbacim nepotrebne opcije.
Moj predlog bi bio da napravimo jedan univerzalni (bazni) sys.txt, i da ga polako nadogradjujemo u zavisnosti od verzija koje koristimo. U prilogu dostavljam sys.txt za razlicite verzije Igo, koji se u sustini razlikuju u malo detalja, osim AvicSync verzije.
 

Prilozi

  • Avic_sys.txt
    4,4 KB · Pregleda: 71
  • basar_sys.txt
    2,7 KB · Pregleda: 49
  • Szulin_sys.txt
    2,3 KB · Pregleda: 46
  • truck_sys.txt
    3,6 KB · Pregleda: 45
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
Tako, samo konkretno! Ovu poruku sto sada pisem veceras menjam drugom konkretnom porukom, tj ostalim sto imam. Trenutno sam u guzvi pa ne mogu da kacim ali sam upao na kratko

Послато са SM-N920C уз помоћ Тапатока
 
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
nomedia je program kojim možete da sakrijete slike koje ne želite da vidite u galeriji, a koje se nalaze u folderu iGO koji ste kopirali na vaš telefon
 

Prilozi

  • nomedia - krije slike iz iGO fodlera.jpg
    nomedia - krije slike iz iGO fodlera.jpg
    578,6 KB · Pregleda: 200
Poslednja izmena:
Član
Učlanjen(a)
15.04.2011
Poruka
1.374
KOPIRANJE iGO FOLDERA U SLUČAJU KADA JE TEL KITKAT I VIŠE



kit-kat 4.4.x nema dozvolu upisa bilo kakvih podataka na eksternu sd karticu.

Postoje 3 rešenja:

1. kopirati sve na internu memoriju
2. odraditi root pa instalirati apk sdfix
3. podeliti , osnova na internu(data.zip, license folder, sys.txt, content(global_cfg folder, lang folder, voice folder)
ostalo iz content foldera na externu
imenovati folder iGO_EXT i unutra strpati content folder sa ostatakom building, car, dem, map, map_HR.....i ostalo)



u sys.txt upisati pod:

[folders]
has_secondary_root=1
android_secondary_root_path="/storage/sdcard1/iGO_EXT"

*nije svuda /storage/sdcard1/
negde je drugačije, a to zavisi od modela telefona i to se može videti ulaskom u svaki filemanager (mislim na putanju i naziv particije gde je memorijska kartica)

na nekim Lolipop 5.0.2 se dešava da nema save foldera na externoj kartici, zbog čega, nije utvrđeno.

primeniti pod 1 ili 3 , pod 2 ne verujem da će pomoći.
 
Natrag
Top